Publication Date: Nov 20, 2026
Calibrate the pouring system of your PU sandwich panel machine. Relieve pressure, check pipelines, adjust pump flow and material ratio, tune the mixing head, and run foaming tests for stable pouring and consistent panel quality.
Calibrating the pouring system of a PU sandwich panel making machine starts with shutting down the equipment and relieving residual pressure inside the material pipelines, then conducting a visual inspection of mixing heads, delivery hoses and metering pumps to rule out blockage and leakage. After that, perform material weighing tests for the two PU components separately to adjust the output flow of each metering pump, fine-tune the mixing ratio to match the required formula, test the discharging uniformity of the mixing head, check the pouring speed and track the foaming effect of the sample panels, and repeat adjustments until stable pouring and qualified foaming results are achieved.

Before starting calibration work, all safety protection measures must be put in place. Wear protective gloves, goggles and breathable protective gear to avoid direct contact with isocyanate and polyol raw materials. Clean the mixing chamber and discharge channel of the pouring system thoroughly to remove residual cured PU foam, which may affect flow accuracy and mixing quality. Check the connection tightness of all pipelines, joints and sealing rings. Replace aging or damaged sealing parts in advance to prevent material leakage during the calibration process. Keep the raw material storage tanks at a stable working temperature, because the viscosity of PU raw materials changes obviously with temperature fluctuations, and unstable temperature will lead to inaccurate flow measurement and failed calibration. Prepare an electronic weighing device with proper precision, clean receiving containers and recording tools to collect data during the flow test. Isolate other unrelated running units of the PU sandwich panel machine to avoid vibration interference when testing the pouring system.
The metering pump group is the core part that controls the feeding volume of the two PU raw materials. Open the independent discharge bypass of each material pipeline, and collect the discharged material into the container within a fixed time period for weighing. Compare the actual measured weight with the target feeding amount, and adjust the pump speed and stroke parameters step by step. Make small adjustments each time instead of large parameter changes, and wait for the flow state to stabilize before carrying out the next weighing record. After the single-channel flow meets the preset value, adjust the feeding ratio between the two components. The matching ratio directly determines the crosslinking reaction of PU foam, the density and bonding performance of the finished sandwich panel. After adjusting the ratio, carry out multiple groups of repeated sampling tests to ensure that the feeding error stays within a controllable range. Do not adjust only according to the theoretical display value on the control panel; physical weighing verification is essential.
Even if the feeding ratio of raw materials is accurate, poor mixing will cause local incomplete reaction and uneven foam inside the sandwich panel. Start the low-speed test operation of the mixing head, observe the spraying state of the mixed material. Adjust the rotating speed of the mixing shaft to get a fine and uniform mixed material stream without material segregation. Then adjust the moving speed and discharging aperture of the pouring trolley. Match the pouring output flow with the advancing speed of the substrate, so that the mixed PU material can be evenly distributed on the surface of the core material or panel substrate without material accumulation or missing pouring areas. Run short trial pouring sections and check the spreading range of the liquid material. Modify the swing range of the mixing head if the material distribution width cannot cover the required panel width. At this stage, focus on the consistency of material distribution along the whole length of the test substrate.
After finishing parameter adjustment of feeding and mixing, carry out real foaming test on trial panels. Observe the foaming rising speed, foam pore structure, surface adhesion and curing state of the PU layer. If the foam shows brittle texture, shrinkage, large pores or poor adhesion with the face sheet, it means the mixing ratio, pouring speed or material temperature still needs fine correction. Make tiny modifications to the metering parameters or mixing speed one item at a time, so that the influence of each adjustment can be distinguished. After each adjustment, produce new test samples for comparison. When continuous test samples show stable foaming structure, uniform density and good bonding effect, the preliminary calibration is completed. Keep all the final parameter records for subsequent reference in daily production.
After calibration, run the pouring system under low load for a period of time to confirm no drift of flow parameters and no leakage at pipeline joints. Clean the mixing head and material channels in time according to the cleaning procedure to prevent residual raw materials from solidifying and blocking the structure. In daily production, regular spot check and re-calibration are necessary. Long-time operation will bring wear to pump internal parts and mixing components, which will slowly change the feeding accuracy. Sudden changes of raw material batches and ambient temperature also require simple re-verification of the pouring system. Form a regular inspection habit to maintain the long-term stability of the pouring system and reduce the reject rate of PU sandwich panels caused by abnormal pouring.
Tags: pu sandwich panel making machine, pu sandwich panel making machine manufacturer, pu sandwich panel making machine supplier, china pu sandwich panel making machine, pu sandwich panel making machine for sale
Are you interested in our continuous sandwich panel line?